
Zion Code and Description
Zion Code |
Zion Description |
7213040 |
10G SFP+ ZR 1550nm 80KM LC SMF Fiber Optic Transceiver |
Applications
- 10G Base-ZR/ZW
- 10G SONET/SDH, OTU2/2e
STANDARD
- Compliant to SFP+ SFF-8431
- Compliant with SFF-8427
- Compliant with IEEE 802.3ae 10GBASE-ZR and 10GBASE-ZW
- Compliant with IEC 60825-1 Class 1 laser eye safe
- RoHS Compliant.
Description
7213040 10G SFP+ ZR compatible SFP+ transceiver supports up to 80Km link lengths over SMF via an LC duplex connector. Digital diagnostics monitoring is available via a 2-wire serial interface, as specified in SFF-8472. Each SFP+ transceiver module is individually tested to be used on a series of Cisco switches, routers, servers, network interface card (NICs) etc. Featuring low power consumption, high speed, this 10G SFP+ transceiver is ideal for data center, enterprise wiring closet, service provider transport application, Radio & Baseband Unit, etc
Main product parameters
Form Factor |
SFP+ |
Vendor Name |
Zion Communication |
Wavelength |
1550nm |
Max Data Rate |
11.3 Gbps |
Max Cable Distance |
80km |
Connector type |
Duplex LC |
Fiber cable Type |
SMF |
|
|
Transimitter Type |
EML |
Receiver Type |
APD |
Transmit Power |
0~4 dBm |
Receiver sensitivity |
-23 ~-6 dBm |
DDM |
Supported |
Operating Temp. |
0°C to 70°C (32°F to 158°F) |
Zion Communication’s Hot 10G transceiver types
Zion Code |
Zion Description |
7213010 |
10G SFP+ SR 850nm 300M LC MMF Fiber Optic Transceiver |
7213020 |
10G SFP+ LR 1310nm 10KM LC SMF Fiber Optic Transceiver |
7213030 |
10G SFP+ ER 1550nm 40KM LC SMF Fiber Optic Transceiver |
7213040 |
10G SFP+ ZR 1550nm 80KM LC SMF Fiber Optic Transceiver |
7213050 |
10G SFP+ BIDI LR 1270/1330nm 10KM LC SMF Fiber Optic Transceiver |
7213060 |
10G SFP+ BIDI LR 1270/1330nm 20KM LC SMF Fiber Optic Transceiver |
7213070 |
10G SFP+ BIDI ER 1270/1330nm 40KM LC SMF Fiber Optic Transceiver |
7213080 |
10G SFP+ BIDI ER 1270/1330nm 60KM LC SMF Fiber Optic Transceiver |
7213090 |
10G SFP+ BIDI ZR 1490/1550nm 80KM LC SMF Fiber Optic Transceiver |
7213110 |
10G SFP+ CWDM 10KM LC SMF Fiber Optic Transceiver |
7213120 |
10G SFP+ CWDM 20KM LC SMF Fiber Optic Transceiver |
7213130 |
10G SFP+ CWDM 40KM LC SMF Fiber Optic Transceiver |
7213140 |
10G SFP+ CWDM 80KM LC SMF Fiber Optic Transceiver |
7213210 |
10G SFP+ DWDM 40KM LC SMF Fiber Optic Transceiver |
7213220 |
10G SFP+ DWDM 80KM LC SMF Fiber Optic Transceiver |
Read More
Detailed product specifications
1 Absolute Maximum Ratings
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Ref. |
Maximum Supply Voltage |
Vcc3 |
-0.5 |
|
4 |
V |
|
Storage Temperature |
TS |
-40 |
|
85 |
°C |
|
Operating Relative Humidity |
RH |
|
|
88 |
% |
|
Case Operating Temperature |
Tcase |
-5 |
|
70 |
°C |
|
Receiver Damage Threshold |
|
6 |
|
|
dBm |
|
2 Electrical Characteristics (Tcase= -5 to 70 ℃, VCC3 = 3.13 to 3.47 Volts)
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Ref. |
Supply Voltage |
Vcc3 |
3.13 |
|
3.47 |
V |
|
Supply Current |
Icc |
|
|
450 |
mA |
|
Module total power |
P |
|
|
1.5 |
W |
1 |
Transmitter |
|
|
|
|
|
|
Input differential impedance |
Rin |
|
100 |
|
Ω |
1 |
Differential data input swing |
Vin,pp |
360 |
|
1400 |
mV |
|
Transmit Disable Voltage |
VD |
2 |
|
Vcc3 |
V |
|
Transmit Enable Voltage |
VEN |
GND |
|
GND+ 0.8 |
V |
|
Transmit Disable Assert Time |
|
|
|
10 |
us |
|
Transmit Disable De-assert Time |
|
|
|
2 |
ms |
|
Receiver |
|
|
|
|
|
|
Differential data output swing |
Vout-pp |
400 |
650 |
800 |
mV |
2 |
Data output rise and fall time |
Tr,Tf |
30 |
|
|
ps |
3 |
LOS Fault |
Vlos-fault |
2 |
|
Vcc-host |
V |
4 |
LOS Normal |
Vlos-nor |
GND |
|
GND+0.8 |
V |
4 |
Notes:
1.Connected directly to TX data input pins.
2.Input 100Ω differential termination.
3.These are unfiltered 20-80% values
4.LOS is an open collector output. Should be pulled-up with 4.7k Ω-10 k Ω on the host board.
Normal operation is logic 0, loss of signal is l
3 Optical Characteristics (Tcase = -5 to 70 ℃, VCC3 = 3.13 to 3.45 Volts)
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Ref. |
Transmitter |
|
|
|
|
|
|
Average Optical Power |
PAVE |
-1 |
|
5 |
|
1 |
Optical Wavelength |
λ |
1530 |
1550 |
1565 |
nm |
|
Side-Mode Suppression ratio |
SMSR |
30 |
|
|
dB |
|
SMSR |
|
30 |
|
|
dB |
|
Optical Extinction Ratio |
ER |
8.2 |
|
|
dB |
|
Transmitter and Dispersion Penalty |
TDP |
|
|
3 |
dB |
|
Average Launch power of OFF transmitter |
POFF |
|
|
-30 |
dBm |
|
Output Eye Mask |
Compliant with IEEE 0802.3ae |
Receiver |
|
|
|
|
|
|
Receiver Sensitivity |
RSENS |
|
|
-23 |
dBm |
2 |
Input Saturation Power (Overload) |
Psat |
-6 |
|
|
dBm |
|
Wavelength Range |
λC |
1270 |
|
1610 |
nm |
|
LOS De-Assert |
LOSD |
|
|
-26 |
dBm |
|
LOS Assert |
LOSA |
-35 |
|
|
dBm |
|
LOS Hysteresis |
|
0.5 |
|
5 |
dB |
|
Notes:
1.Average power figures are informative only, per IEEE 802.3ae.
2.Measured with conformance test signal for BER = 10^–12.@10.3125Gbps, PRBS=2^31-1,NRZ
4 Pin Descriptions

Diagram of Host Board Connector Block Pin Numbers and Name
5 Transceiver Block Diagram
Pin |
Symbol |
Name/Description |
NOTE |
1 |
VEET |
Transmitter Ground |
1 |
2 |
Tx_FAULT |
Transmitter Fault. |
2 |
3 |
Tx_DISABLE |
Transmitter Disable. Laser output disabled on high or open. |
3 |
4 |
SDA |
2-wire Serial Interface Data Line |
2 |
5 |
SCL |
2-wire Serial Interface Clock Line |
2 |
6 |
MOD_ABS |
Module Absent. Grounded within the module |
4 |
7 |
RS0 |
No connection required |
|
8 |
RX_LOS |
Loss of Signal indication. Logic 0 indicates normal operation. |
2 |
9 |
RS1 |
No connection required |
|
10 |
VEER |
Receiver Ground |
1 |
11 |
VEER |
Receiver Ground |
1 |
12 |
RD- |
Receiver Inverted DATA out. AC Coupled |
|
13 |
RD+ |
Receiver DATA out. AC Coupled |
|
14 |
VEER |
Receiver Ground |
1 |
15 |
VCCR |
Receiver Power Supply |
|
16 |
VCCT |
Transmitter Power Supply |
|
17 |
VEET |
Transmitter Ground |
1 |
18 |
TD+ |
Transmitter DATA in. AC Coupled |
|
19 |
TD- |
Transmitter Inverted DATA in. AC Coupled. |
|
20 |
VEET |
Transmitter Ground |
1 |
Note:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.13Vand 3.6V.
3. Tx_ Disable is an input contact with a 4.7 kΩ to 10 kΩ pull-up to VccT inside the module
4. Mod_ ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to
Vcc_ Host with a resistor in the range 4.7 kΩ to10 kΩ.Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host slot.
6 Digital Diagnostic Functions
As defined by the SFP MSA, Fiberate’s SFP+ transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters:
• Transceiver temperature
• Laser bias current
• Transmitted optical power
• Received optical power
• Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range.
The SFP MSA defines a 256-byte memory map in EEPROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h).The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged.
The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.
7 Host – Transceiver Interface Block Diagram

8 Outline Dimensions

Download
