Name: 10G SFP+ TO SFP+ Active Optical Cable
SKU: 7216060

Zion Code and Description

Zion Code	Zion Description
7216060	10G SFP+ TO SFP+ Active Optical Cable

Applications

25GBASE-SR4 100G Ethernet Links; InfiniBand QDR applications
Servers, switches, storage and host card adap

Description

The 7216060 10G SFP+ active optic cables are a high performance, low power consumption,
long reach interconnect solution supporting 10G Ethernet ,or Infini BandQDR/DDR/SDR,
12.5G/10G/8G/4G/2G fiber channel ,PCIe and SAS.

It is specially designed for high-speed, short-range data links via optical fiber lines.
SFP+ AOC provides signal integrity, longer distance, superior electromagnetic immunity
and better bit error rate. It is a cost-effective solution for data center/storage
and all short-range data applications.

Main product parameters

Connector Type	SFP+ to SFP+	Vendor Name	Zion Communication
Max Data Rate	10Gbps	Fiber cable Type	MMF
Max Cable Distance 1	70m on OM3 MMF	Max Cable Distance 2	100m on OM4 MMF
Transimitter Type	VCSEL	Receiver Type	PIN
Wavelength	850nm	CDR	Support
Power Supply	3.3V	Operating Temp.	0°C to 70°C (32°F to 158°F)

Outline Drawing

Zion Code		Zion Description
7216010		100G QSFP28 TO QSFP28 Active Optical Cable
7216020		100G QSFP28 TO 4×SFP28 Active Optical Cable
7216030		40G QSFP+ TO QSFP+ Active Optical Cable
7216040		40G QSFP+ TO 4×SFP+ Active Optical Cable
7216050		25G SFP28 TO SFP28 Active Optical Cable
7216060		10G SFP+ TO SFP+ Active Optical Cable

1. Absolute Maximum Ratings

Parameter	Symbol	Min.	Typical	Max.	Unit
Storage Temperature (℃）	TS	-10		70	°C
Relative Humidity	RH	5		85	%
Power Supply Voltage	VCC	-0.5		3.6	V

2. Recommended Operating Environment

Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Case operating Temperature	TOP	0		70	°C
Power Supply Voltage	VCC	3.14	3.3	3.47	V
Power Dissipation	Pd			0.6	W
Data Rate	BR		10.3125		Gbps	Each Channel
Transmission Distance with	TD	0		100	m	OM4

3. Electrical Characteristics for SFP+

Parameter		Symbol	Min.	Typical	Max.	Unit
Transmitter
Differential data input swing		Vin.pp	200		1000	mV
Input Differential Impedance		ZD	90	100	110	Ω
Tx_Fault	Normal Operation	VOL	0		0.8	V
Tx_Fault	Transmitter Fault	VOH	2		Vcc+0.3	V
Tx_Disable	Normal Operation	VIL	0		0.8	V
Tx_Disable	Laser Disable	VIH	2		Vcc+0.3	V
Receiver
Differential data output swing		Vin.pp	200		800	mV
Bit Error Rate (1 prbs2^31-1@25.78125Gbps)		BER			E-12
Input Differential Impedance		Zin	90	100	110	Ω
Rx_LOS	Normal Operation	VOL	0		0.8	V
Rx_LOS	Lose Signal	BER	2		Vcc+0.3	V

4. Pin Assignment

10G SFP+ TO SFP+ Active Optical Cable-2

5. Pin description

Pin	Symbol	Name/Description	NOTE
1	VEET	Transmitter Ground (Common with Receiver Ground)	1
2	TFAULT	Transmitter Fault.	2
3	TDIS	Transmitter Disable. Laser output disabled on high or open.	3
4	SDA	2-wire Serial Interface Data Line	4
5	SCL	2-wire Serial Interface Clock Line	4
6	MOD_ABS	Module Absent. Grounded within the module	4
7	RS0	Rate Select 0	5
8	LOS	Loss of Signal indication. Logic 0 indicates normal operation.	6
9	RS1	No connection required	1
10	VEER	Receiver Ground (Common with Transmitter Ground)	1
11	VEER	Receiver Ground (Common with Transmitter Ground)	1
12	RD-	Receiver Inverted DATA out. AC Coupled
13	RD+	Receiver Non-inverted DATA out. AC Coupled
14	VEER	Receiver Ground (Common with Transmitter Ground)	1
15	VCCR	Receiver Power Supply
16	VCCT	Transmitter Power Supply
17	VEET	Transmitter Ground (Common with Receiver Ground)	1
18	TD+	Transmitter Non-Inverted DATA in. AC Coupled.
19	TD-	Transmitter Inverted DATA in. AC Coupled.
20	VEET	Transmitter Ground (Common with Receiver Ground)	1

Note:

1.Circuit ground is internally isolated from chassis ground.
2.TFAULT is an open collector/drain output, which should be pulled up with a 4.7kΩ– 10 kΩ resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V.
3.Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
4.Should be pulled up with 4.7kΩ- 10kΩ on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in.
5.Internally pulled down per SFF-8431 Rev 4.1.
6.LOS is open collector output. It should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V.
Logic 0 indicates normal operation; logic 1 indicates loss of signal.

10G SFP+ TO SFP+ Active Optical Cable

Zion Code and Description

Applications

Description

Main product parameters

Outline Drawing