7213050 10G SFP+ BIDI LR 1270/1330nm 10KM LC SMF Fiber Optic Transceiver is small form factor pluggable module for optical data communications such as 10GBASE-LR/LW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability. The 7213050 module is designed for single mode fiber and operates at a nominal wavelength of 1270nm or 1330nm; The transmitter section uses a multiple quantum well DFB, which is class 1 laser compliant according to International Safety Standard IEC-60825.The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. The transceiver designs are optimized for high perform -ance and cost effective to supply customers the best solutions for telecommunication.
Note: Stress in excess of the maximum absolute ratings can cause permanent damage to the transceiver.
2 General Operating Characteristics
Operating Case Temp
3 Electrical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 80 ℃,VCC = 3.13 to 3.47 V)
Differential data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Input differential impedance
Differential data output swing
Output rise time and fall time
1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
2. Into 100Ω differential termination.
3. 20 – 80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s sequence in the PRBS 9 is an acceptable alternative.
4. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0;
loss of signal is logic 1.
4 Optical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 80 ℃, VCC = 3.13 to 3.47 V)
Ave. output power (Enabled)
Side-Mode Suppression Ratio
RMS spectral width
Rise/Fall time (20%~80%)
Relative Intensity Noise
Output Optical Eye
Compliant with IEEE 0802.3ae
Average Receive Power
1. Average power figures are informative only, per IEEE 802.3ae.
2. Measured with worst ER; BER<10-12; 231 – 1 PRBS.
5 Pin Defintion And Functions
6 Transceiver Block Diagram
Transmitter Disable. Laser output disabled on high or open
2-wire Serial Interface Data Line
2-wire Serial Interface Clock Line
Module Absent. Grounded within the module
Rate Select 0
Loss of Signal indication. Logic 0 indicates normal operation
Rate Select 1
Receiver Inverted DATA out. AC Coupled
Receiver DATA out. AC Coupled
Receiver Power Supply
Transmitter Power Supply
Transmitter DATA in. AC Coupled
Transmitter Inverted DATA in. AC Coupled
1.Module circuit ground is isolated from module chassis ground within the module.
2.should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
3.Tx_Disable is an input contact with a 4.7 kΩ to 10 kΩ pullup to VccT inside the module.
4.Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to Vcc_Host with a resistor in the range 4.7 kΩ to10 kΩ.Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host slot.
7 Serial Interface for ID and DDM
The 7213050 10G SFP+ BIDI LR 1270/1330nm 10KM LC SMF Fiber Optic Transceiver support the 2-wire serial communication protocol as defined in the SFP+ MSA. The standard SFP+ serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, This SFP+ transceivers provide an enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range.
The SFP MSA defines a 256-byte memory map in EEPROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X(A0h), so the originally monitoring interface makes use of the 8 bit address(A2h), so the originally defined serial ID memory map remains unchanged. The structure of the memory map is shown in Table1.
8 Digital Diagnostic Specifications
Transceiver supply voltage
Transmitter bias current
Transmitter output power
Receiver average input power
1.When Operating temp.=0~70 ºC,the range will be min=-5,Max=+75
2. Internally measured
3. The accuracy of the Tx bias current is 10% of the actual current from the laser driver to the laser
9 Typical Interface Circuit
10 Recommended power supply filter
Inductors with DC resistance of less than 1Ω should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage. When the recommended supply filtering network is used, hot plugging of the SFP transceiver module will result in an inrush current of no more than 30 mA greater than the steady state value
11 Package Dimensions
Email us, Call us, Meeting online with us!
Tell us about your purchasing plans!
We specializing in designing, manufacturing communications infrastructure & equipment and providing customized services for our customers！